Mr Surfacer

Got a question about techniques, materials or other aspects of physically building a model? This is the place to ask.

Moderators: DasPhule, Moderators

Go Flight
Posts: 3666
Joined: Thu Feb 06, 2003 9:54 pm
Location: Staten Island
Contact:

Post by Go Flight »

If anyone cares and FWIW, I just started using the 500 and 1000 and found (by accident) that it cleans up very nicely with acetone.
User avatar
Jagdson
Posts: 8738
Joined: Mon Jul 15, 2002 8:27 pm
Location: Hunched over my keyboard like a *pothoc* vulture, cursing my inability to properly budget my time.

Post by Jagdson »

It sounds like Mister is great stuff, the kind of stuff I could really use on all my projects... as long as it's mixed properly and used according to the product number/end purpose parameters.

Whee.

I need to spit in Tamiya paints to keep them workable, for Ghid's sake. Are there any Mister Products that can just be used?
Science created airplanes and skyscrapers, but it took faith to bring them together.

Trust me. I'm a priest.
User avatar
Mr. Badwrench
Posts: 9587
Joined: Fri Jul 12, 2002 6:31 pm
Location: Wheatridge, Co.

Post by Mr. Badwrench »

Unless I'm airbrushing, I just use Mr. Surfacer straight out of the jar. If I am airbrushing, (and only with 1200), I mix it 1:1 with lacquer thinner. It doesn't have to be precise, I've tried as far as 3:5 and 5:3 either way. The thicker you mix it, the more likely it will clog, and the thinner the mix, the lower the air pressure you'll need, but that goes for any paint.
I speak of the pompatous of plastic.
Thomas E. Johnson
Posts: 2821
Joined: Fri Jan 23, 2004 10:56 pm
Location: Up The Street From Uncle Sam's House

Post by Thomas E. Johnson »

I've been playing with this stuff out of the bottle now for a few weeks, and I haven't observed it filling in any small imperfections at all. It just conforms to the surface, including any imperfections, and leaves them visable. I see no point in thinning it for airbrushing, since the stuff can be had in a rattle can. In all honesty, I see no diffrence between this product, and regular primer, like Tamyia.
Thomas E. Johnson
User avatar
Blappy
Moderator
Posts: 8559
Joined: Thu Jul 11, 2002 5:35 pm
Location: Such Great Heights
Contact:

Post by Blappy »

:roll:

OK it sux. Everyone send me their useless ineffective Mr.Surfacer and I will properly dispose of it for them. :twisted:
BUILDING THE FUTURE!

"In the universe, space travel may be the normal birth pangs of an otherwise dying race. A test. Some races pass, some fail."
- Robert A. Heinlein


Our only chance of long-term survival is not to remain lurking on planet Earth, but to spread out into space.
- Stephen Hawking, 2011

The Blaposphere
User avatar
TER-OR
Site Admin
Posts: 10531
Joined: Thu Jul 11, 2002 7:05 pm
Location: Conjugate imprecision of time negates absolute determination of location.
Contact:

Post by TER-OR »

Thomas E. Johnson wrote:I've been playing with this stuff out of the bottle now for a few weeks, and I haven't observed it filling in any small imperfections at all. It just conforms to the surface, including any imperfections, and leaves them visable. I see no point in thinning it for airbrushing, since the stuff can be had in a rattle can. In all honesty, I see no diffrence between this product, and regular primer, like Tamyia.

You need to buff the surface after spraying. Not sand it all down to the surface, but buff it. Use the hand-brushed product to fill seams or scratches. The spray-on is quite thin coat, and will work well if you use a very fine wet-buffing pad to smooth the surface. Don't expect miracles without a bit of work.
Raised by wolves, tamed by nuns, padded for your protection.

Terry Miesle
Never trust anyone who says they don't have a hobby.
Quando Omni Flunkus Moratati
Thomas E. Johnson
Posts: 2821
Joined: Fri Jan 23, 2004 10:56 pm
Location: Up The Street From Uncle Sam's House

Post by Thomas E. Johnson »

TER-OR wrote:
Thomas E. Johnson wrote:I've been playing with this stuff out of the bottle now for a few weeks, and I haven't observed it filling in any small imperfections at all. It just conforms to the surface, including any imperfections, and leaves them visable. I see no point in thinning it for airbrushing, since the stuff can be had in a rattle can. In all honesty, I see no diffrence between this product, and regular primer, like Tamyia.

You need to buff the surface after spraying. Not sand it all down to the surface, but buff it. Use the hand-brushed product to fill seams or scratches. The spray-on is quite thin coat, and will work well if you use a very fine wet-buffing pad to smooth the surface. Don't expect miracles without a bit of work.
The hand brushed stuff is what I've been trying. The Mr. Surfacer 500 acts more like thin putty, and it shrinks as it cures, leaving the imperfection still visable. the 1000 stuff is so thin it seems like grey primer, and it conforms to the surface, imperfections and all. I end up having to use coat after coat, with lots of wet sanding to get any results.
Thomas E. Johnson
macfrank
Posts: 8726
Joined: Fri Oct 11, 2002 6:55 pm
Location: Los Angeles, CA
Contact:

Post by macfrank »

Thomas E. Johnson wrote: The hand brushed stuff is what I've been trying. The Mr. Surfacer 500 acts more like thin putty, and it shrinks as it cures, leaving the imperfection still visable. the 1000 stuff is so thin it seems like grey primer, and it conforms to the surface, imperfections and all. I end up having to use coat after coat, with lots of wet sanding to get any results.
Surface prep is really important; one thin coat of primer to find the surface imperfections, fix those and then add another coat.

If you want to use it to fill in holes with Mr. Surfacer, mix it with a little baby powder or micro balloons (I haven't tried corn starch). It'll form a putty that won't shrink as much. Remove the excess with denatured alcohol or acetone.

Also, make sure you're really stirring up Mr. Surfacer before you decant it. The particles will form a layer at the bottom that can take some vigorous stirring before they go back into suspension.

Frank
User avatar
Jagdson
Posts: 8738
Joined: Mon Jul 15, 2002 8:27 pm
Location: Hunched over my keyboard like a *pothoc* vulture, cursing my inability to properly budget my time.

Post by Jagdson »

Also, keep in mind that really big blemishes should get actual putty, or gap-filling superglue, beforehand. By "really big" I mean anything wider or deeper than a bad X-acto scratch, and even some of those are questionable.
Science created airplanes and skyscrapers, but it took faith to bring them together.

Trust me. I'm a priest.
User avatar
TER-OR
Site Admin
Posts: 10531
Joined: Thu Jul 11, 2002 7:05 pm
Location: Conjugate imprecision of time negates absolute determination of location.
Contact:

Post by TER-OR »

I use Mr. Surfacer to fill some pretty big gaps - or complete the fill started with epoxy putty sometimes. As I mentioned, you will need to build it up a bit.
Raised by wolves, tamed by nuns, padded for your protection.

Terry Miesle
Never trust anyone who says they don't have a hobby.
Quando Omni Flunkus Moratati
bjackw
Posts: 4
Joined: Sun Oct 15, 2006 6:46 pm
Location: Atlanta, GA

Where to buy?

Post by bjackw »

Ok. I'm sold on giving Mr. Surfacer 1200 a go. The only question is: where can I buy it? None of my local (Atlanta, GA) hobby shops seem to carry it. What are the online options?
Go Flight
Posts: 3666
Joined: Thu Feb 06, 2003 9:54 pm
Location: Staten Island
Contact:

Post by Go Flight »

While it may be a slightly expensive way to see the technique - Floyd Werner has an excellent Mr. surfacer demo filling sink holes in his Master Class Videos DVD = http://www.masterclassmodels.com/disk1.html
Yeah he's building a WW2 plane, but the techniques are universal.
macfrank
Posts: 8726
Joined: Fri Oct 11, 2002 6:55 pm
Location: Los Angeles, CA
Contact:

Post by macfrank »

Mr. Surfacer is actually a car paint primer; David Meriman thinks that an equivalent is Lucite 131S primer (or its equivalent). If you need a lot, this is by far the cheapest route.

If you don't want to go to a car paint/refinishing store, you can get it from Squadron, or Megahobby.

Frank
bjackw
Posts: 4
Joined: Sun Oct 15, 2006 6:46 pm
Location: Atlanta, GA

Post by bjackw »

Thanks for the info. I ordered all 3 versions (500, 1000, 1200) from Squadron. I'll also pick up some of the Lucite and do a comparision test...
User avatar
Blappy
Moderator
Posts: 8559
Joined: Thu Jul 11, 2002 5:35 pm
Location: Such Great Heights
Contact:

Post by Blappy »

And if you find a Blue coloured material that LOOKS like Mr.Surface don't be fooled, That's......




















Mr Smurfacer

A smaller and not as effective substance designed for Fungi. :lol:
BUILDING THE FUTURE!

"In the universe, space travel may be the normal birth pangs of an otherwise dying race. A test. Some races pass, some fail."
- Robert A. Heinlein


Our only chance of long-term survival is not to remain lurking on planet Earth, but to spread out into space.
- Stephen Hawking, 2011

The Blaposphere
User avatar
Lt. Z0mBe
Posts: 7311
Joined: Thu May 29, 2003 1:46 pm
Location: Balltown Kentucky, by God!
Contact:

Post by Lt. Z0mBe »

macfrank wrote:Mr. Surfacer is actually a car paint primer; David Meriman thinks that an equivalent is Lucite 131S primer (or its equivalent). If you need a lot, this is by far the cheapest route.

If you don't want to go to a car paint/refinishing store, you can get it from Squadron, or Megahobby.

Frank
Could this Lucite be had at Autozone or its equivalent? I've been hearing you all rave about it. I figured it might be worth a go.

Kenny

www.sigmalabsinc.com


Onward, proud eagle, to thee the cloud must yield.
User avatar
TER-OR
Site Admin
Posts: 10531
Joined: Thu Jul 11, 2002 7:05 pm
Location: Conjugate imprecision of time negates absolute determination of location.
Contact:

Post by TER-OR »

AKA Sand and Fill
It's pretty similar to the Surfacer 500.
Raised by wolves, tamed by nuns, padded for your protection.

Terry Miesle
Never trust anyone who says they don't have a hobby.
Quando Omni Flunkus Moratati
User avatar
woozle
Posts: 15365
Joined: Mon Aug 05, 2002 1:40 pm
Location: Vancouver (not BC), Washington (not DC)
Contact:

Post by woozle »

Nice Thing about Mr. Surfacer is that it doesn't fill/cover details while it doesn't smooth-over scratches. I use it as well as Aves for big fills and Squadron for small fills.
"A Good Magician never reveals how a trick is done.... and an EVIL magician never leaves any evidance that there was a trick in the first place!"
-Kaja Phoglio
Girl Genius (advanced class)
macfrank
Posts: 8726
Joined: Fri Oct 11, 2002 6:55 pm
Location: Los Angeles, CA
Contact:

Post by macfrank »

Lt. Z0mBe wrote: Could this Lucite be had at Autozone or its equivalent? I've been hearing you all rave about it. I figured it might be worth a go.

Kenny
Kenny, the only place I've found it online is here

$99... I think I'll stick with Mr. Surfacer bottles until I need a gallon of the stuff.
User avatar
Blappy
Moderator
Posts: 8559
Joined: Thu Jul 11, 2002 5:35 pm
Location: Such Great Heights
Contact:

Post by Blappy »

macfrank wrote:
Lt. Z0mBe wrote: Could this Lucite be had at Autozone or its equivalent? I've been hearing you all rave about it. I figured it might be worth a go.

Kenny
Kenny, the only place I've found it online is here

$99... I think I'll stick with Mr. Surfacer bottles until I need a gallon of the stuff.
OOoh! Good price. I need to get one of these. I blow (no pun intended!) through primer like crazy.
BUILDING THE FUTURE!

"In the universe, space travel may be the normal birth pangs of an otherwise dying race. A test. Some races pass, some fail."
- Robert A. Heinlein


Our only chance of long-term survival is not to remain lurking on planet Earth, but to spread out into space.
- Stephen Hawking, 2011

The Blaposphere
User avatar
zysurge
Posts: 1029
Joined: Mon May 24, 2004 2:49 pm
Location: Connecticut
Contact:

Post by zysurge »

macfrank wrote:Kenny, the only place I've found it online is here

$99... I think I'll stick with Mr. Surfacer bottles until I need a gallon of the stuff.
I bought a quart of Fill-n-Sand 131S on e*ay fro less than $30. If you don't need a full gallon, it's an economical alternative.

Eric
bjackw
Posts: 4
Joined: Sun Oct 15, 2006 6:46 pm
Location: Atlanta, GA

Post by bjackw »

eBay! That's a great find. After several days of searching with no luck locally, I also just ordered a quart via eBay.
User avatar
Lt. Z0mBe
Posts: 7311
Joined: Thu May 29, 2003 1:46 pm
Location: Balltown Kentucky, by God!
Contact:

Post by Lt. Z0mBe »

Thanks, frank et.al!

I shall order some up. Perhaps just a quart for me though. :)

Kenny

www.sigmalabsinc.com


Onward, proud eagle, to thee the cloud must yield.
User avatar
Alex Dumas
Posts: 750
Joined: Thu May 01, 2003 6:02 pm
Location: Montreal, Canada
Contact:

Post by Alex Dumas »

Guys, how much time do you let it cure before sanding? ...assuming curing time is the same for both the 500 and 1000 Surfacers.

And what grid of paper do you use for the first strokes at the 500?

Thanks!
Alex
Alex
scihighmodels.com
macfrank
Posts: 8726
Joined: Fri Oct 11, 2002 6:55 pm
Location: Los Angeles, CA
Contact:

Post by macfrank »

Alex Dumas wrote:Guys, how much time do you let it cure before sanding? ...assuming curing time is the same for both the 500 and 1000 Surfacers.

And what grid of paper do you use for the first strokes at the 500?

Thanks!
Alex
You can sand it after a few (2-4) hours, but it'll be pretty soft. If you wait 24 or so, it'll cure to a very hard finish.

But why sand? A dab of denatured alcohol (or acetone, if the material underneath is resin) will remove the excess without sanding.
User avatar
Mr. Badwrench
Posts: 9587
Joined: Fri Jul 12, 2002 6:31 pm
Location: Wheatridge, Co.

Post by Mr. Badwrench »

I've found that you can sand it more quickly than that, within an hour works ok. Macfrank is correct, it won't be fully cured yet, but it is hard enough to sand on without making a mess pretty quickly. As to what grit to use, that depends on how much you need to take off. I'll often start off with a medium sanding stick, (about 600 grit), but sometimes I'll go straight to a fine stick, (about 1000 or 1200 grit), and move up from there.
I speak of the pompatous of plastic.
User avatar
Blappy
Moderator
Posts: 8559
Joined: Thu Jul 11, 2002 5:35 pm
Location: Such Great Heights
Contact:

Post by Blappy »

Alex Dumas wrote:
And what grid of paper do you use for the first strokes at the 500?

Thanks!
Alex
I usualy start with 3200 MicroMesh on the 500 and work up to 4000 or 6000 if its the final polish before paint. For 1000 you can usually go right to 4000 MicroMesh then 6000. If you have a big piece of dust in the paint then that area needs to be started at 3200. Oh and ALWAYS wetsand.
BUILDING THE FUTURE!

"In the universe, space travel may be the normal birth pangs of an otherwise dying race. A test. Some races pass, some fail."
- Robert A. Heinlein


Our only chance of long-term survival is not to remain lurking on planet Earth, but to spread out into space.
- Stephen Hawking, 2011

The Blaposphere
User avatar
Marco Scheloske
Posts: 5251
Joined: Sun Jul 14, 2002 11:08 am
Location: Moenchengladbach, Germany

Post by Marco Scheloske »

800, followed by 1000. That`s it.
Greetings from Germany -
"In glue we trust!" - http://technomaniaweb.jimdo.com

Marco
User avatar
Alex Dumas
Posts: 750
Joined: Thu May 01, 2003 6:02 pm
Location: Montreal, Canada
Contact:

Post by Alex Dumas »

macfrank wrote:But why sand? A dab of denatured alcohol (or acetone, if the material underneath is resin) will remove the excess without sanding.
Do you remove the excess right after applicaton are do you wait a while?

And thanks for your inputs guys!

Alex
Alex
scihighmodels.com
macfrank
Posts: 8726
Joined: Fri Oct 11, 2002 6:55 pm
Location: Los Angeles, CA
Contact:

Post by macfrank »

Alex Dumas wrote: Do you remove the excess right after applicaton are do you wait a while?
I let it dry, then remove the excess with denatured alcohol on a Q-tip or microbrush. It helps to dab some of the alcohol on first, wait a few seconds for it to soften the Mr. Surfacer, then remove the excess. If you remove too much Mr. Surfacer, reapply.

If you wait until the Mr. Surfacer fully cures, you'll have to let the alcohol sit on it longer.

If it's a resin model, Acetone works just as well, if not better. Straight Acetone will attack and soften most styrenes, which is why I mention using Acetone on resin.

Frank
Post Reply