Lighting Help!!!!!!

Got a question about techniques, materials or other aspects of physically building a model? This is the place to ask.

Moderators: DasPhule, Moderators

Post Reply
Trekmanscott
Moderator
Posts: 5901
Joined: Fri Jul 12, 2002 1:13 pm
Location: Pittsburgh, PA

Lighting Help!!!!!!

Post by Trekmanscott »

I'm in a bind and I hope someone out there can help me. I'm in the process of building Ertl's Defiant. I'm building the model so that it light's up. I wired 15 LED's of differing colors inside the model. two of the lights are connected to a 4060 chip so that they blink. Here's my problem. Everything was working just fine when I glued the 2 halves of the model together. Yesterday After I laid down the base coat I removed the paint masks and reconnected the wiring to do a light test and to check for light leaks. Only 1 of the 2 LEDS on the 4060 chip will blink! I have no idea what could be wrong. I'm leaning towards the fact that I need a new battery. The 1st LED in the series will blink, so i'm thinking that there's not enough power in the battery to light the second LED. I can't reopen the model. I used epoxy to glue the aftermarket parts into place. Anyone have any idea what could be causing this, and have any ideas on how I could fix this. I can't reopen the model. I used epoxy to glue the aftermarket parts into place.
"A life is like a garden. Perfect moments can be had, but not preserved, except in memory. LLAP" Leonard Nimoy
Scott Hasty
Posts: 3419
Joined: Fri Jul 12, 2002 4:13 pm
Location: Chesapeake, VA

Post by Scott Hasty »

I'm 99.999999% certain it's not a power issue. I'm equally certain you have a bad connection. Did you solder all the joints?

Scottie
I am fearful when I see people substituting fear for reason
Trekmanscott
Moderator
Posts: 5901
Joined: Fri Jul 12, 2002 1:13 pm
Location: Pittsburgh, PA

Post by Trekmanscott »

I did not solder. I used a wire wrap tool for all of the connections. The whole thing is bizzare. Any suggestions on how to fix it?
"A life is like a garden. Perfect moments can be had, but not preserved, except in memory. LLAP" Leonard Nimoy
User avatar
rossjr
Posts: 3281
Joined: Mon Jul 15, 2002 10:33 am
Location: Minneapolis, MN - Grandkids are Great!

Post by rossjr »

It could be power but it would be better to see a schematic of what you wired. I am concerned that the LED's are in series when I think they should be in parallel, maybe it's just the wrong term you used but it sure would help to identify the problem.
Scott Hasty
Posts: 3419
Joined: Fri Jul 12, 2002 4:13 pm
Location: Chesapeake, VA

Post by Scott Hasty »

Trekmanscott wrote:I did not solder. I used a wire wrap tool for all of the connections. The whole thing is bizzare. Any suggestions on how to fix it?
Well, that brings me to believe you have a broken connection. If it were power, your other LED wouldn't operate (as well as your CMOS chip). Short of cracking it open and fixing it, I cannot think of any other way of getting to it unless you want to cut (or drill) through the area you think the proplem is in.

Scottie
I am fearful when I see people substituting fear for reason
User avatar
MarkW
Posts: 134
Joined: Sun Jan 30, 2005 11:21 am
Contact:

Post by MarkW »

I gotta agree--your best best may be to cut it open in an inconspicuous place and try fixing it.

In general, soldering is my preferred way to go. It is a gaurunteed joint.
MarkW

"If we lose the war in the air, we lose the war, and we lose it quickly."
--Field Marshal Bernard Montgomery

http://mysite.verizon.net/modelwerks/

RAAM FAQ:
http://mysite.verizon.net/modelwerks/ti ... index.html
Sparky
Moderator
Posts: 2404
Joined: Thu Jun 05, 2003 8:28 am
Location: Are we there yet? (Chicago)
Contact:

Post by Sparky »

It is possible that the power is to low to light one light, In fact on Neil's tug there are a red and green led on either seid for nav lights, they are hooked in parallel to the driver circuit but have their own dropping resistor. Since they have different voltage ratings as the battery gets low you can hardly see teh green blining while the red is still visibile. But if the hole thing isn't noticebly dimmer then you probably have a bad contact connection. Also if epoxy or something else managed to get onto a connection that wasn't sodlered it may have isolated the wires enough to brake the electrical connection.
User avatar
LindaSmile
Site Admin
Posts: 13084
Joined: Wed Apr 30, 2003 11:14 am
Location: Chicago

Post by LindaSmile »

Try reversing the polarity.... sorry, I couldn't help myself.

Linda
Is this plastic thingy on the counter a model part or can I throw it away?
Trekmanscott
Moderator
Posts: 5901
Joined: Fri Jul 12, 2002 1:13 pm
Location: Pittsburgh, PA

Post by Trekmanscott »

OK well I bought new batteries and I put them in no good. So I took mark and scott advice and I cut open a smaller area on the model and for some reason the LED was bad. I have No idea what happened to it. Well after about a half hour the LED was replaced and I'm ready to seal the hole. I guess I lost a couple day on this 1 LED but I guess it better that it happened now and not in Louisville :shock: A freaid thought that maybe the gass leaked out of the LED. Who knows. Well I have to go fill in the new "door" I added to the Defiant.

Thanks for the help guys.
"A life is like a garden. Perfect moments can be had, but not preserved, except in memory. LLAP" Leonard Nimoy
User avatar
rossjr
Posts: 3281
Joined: Mon Jul 15, 2002 10:33 am
Location: Minneapolis, MN - Grandkids are Great!

Post by rossjr »

Please tell me that you have a resistor in series with the LED, if not you will be replacing a lot LED's frequently...
Balok
Posts: 1599
Joined: Sun May 04, 2003 11:31 pm
Location: Livermore, CA.

Post by Balok »

Yup, and use solder after you wirewrap.

I use this all the time.
<A HREF="http://ourworld.compuserve.com/homepage ... d.htm">LED Series Calculator</A HREF>
<i>
Always remember
we stand on the roof of Hell
gazing at flowers.
</i>
en'til Zog
Posts: 2405
Joined: Fri Jul 12, 2002 3:03 pm
Location: The Wilds of Northwoods Wisconsin

Post by en'til Zog »

If the LEDs are being driven by an IC like the 4060, they're safe enough with no resistor - even if the chip is being fed 9 volts. I've been using them that way for years, no ill effects to the LEDs.

That's the nice thing about using CMOS chips - the output is 11 milliamps max - safe for any LED. And no, I've never had trouble with the 'excess voltage'. It seems to be the amperage that fries the LEDs rather than too much voltage. IF the amperage is kept down things seem to be fine.

My experience. Your mileage may vary.
Post Reply