How to Know Pin Marks Are Sanded Down **SMOOTH and FLUSH?**

Got a question about techniques, materials or other aspects of physically building a model? This is the place to ask.

Moderators: DasPhule, Moderators

Post Reply
Cenebar
Posts: 2486
Joined: Fri Jul 26, 2002 4:19 pm

How to Know Pin Marks Are Sanded Down **SMOOTH and FLUSH?**

Post by Cenebar »

I sand off pin marks down to what my finger and eyes see as smooth and flush, but when I prime, I see that I didn't sand them down flush enough. So I sand off the primer and the marks again, but I can't tell if they're totally flush or not.

Is there a method to know that the pin marks are smooth and flush before I spray primer? Would handbrushing a layer of paint work?

Thanks.
User avatar
Umi_Ryuzuki
Posts: 3841
Joined: Fri Jul 12, 2002 2:22 pm
Location: PDX, Oregon
Contact:

Post by Umi_Ryuzuki »

That is exactly what sandable primer is for.

You are doing it correctly.

:8)
'
"I have to go now,... because my life is stupid and leprachans are dorks."
Nyow!
/
=^o^=
Whiteraven_2001
Posts: 2636
Joined: Sun Jul 14, 2002 10:14 am

Post by Whiteraven_2001 »

I read somewhere that the best way to check is to paint the questionable area with silver paint. It apparently makes any problems obvious.
User avatar
Lt. Z0mBe
Posts: 7311
Joined: Thu May 29, 2003 1:46 pm
Location: Balltown Kentucky, by God!
Contact:

Post by Lt. Z0mBe »

You may try using a finer grit sandpaper. I do this so that it imparts a bit of shine or "polish" to the area of primer being sanded. This allows you better eyeballing of the area.

I hope this helps.

Kenny

www.sigmalabsinc.com


Onward, proud eagle, to thee the cloud must yield.
Cenebar
Posts: 2486
Joined: Fri Jul 26, 2002 4:19 pm

Post by Cenebar »

Actually, I meant sprue marks :D.

Does the saying, "Sand it down until you don't see it anymore" true?
User avatar
Kylwell
Moderator
Posts: 29643
Joined: Sun Nov 02, 2003 9:25 pm
Location: Lakewood, CO
Contact:

Post by Kylwell »

Two words... Sanding Sticks.

Yes those items made by Squadron or Flex-i-File that look like color coated emory boards and come in multiple grits. Why? Well the semi-soft flat surface enables one to sand the sprue marks flat and then polish them to a gloss finish. One look at the highlight will tell you if you've gone far enough.
Abolish Alliteration
Cenebar
Posts: 2486
Joined: Fri Jul 26, 2002 4:19 pm

Post by Cenebar »

Yep, I use the sanding sticks. I sand the sprue marks flat, but I still see them, which kind of makes me wonder if I need to sand them down until they totally disappear.

To do so makes me wonder if I've gone too far and lost detail, not to mention one side with the sprue mark will be lower than the other side without a sprue mark.

Sanding again after priming's not too bad as long as one doesn't prime over so much detail.
User avatar
Jonas Calhoun
Posts: 1919
Joined: Sun Nov 16, 2003 6:12 pm
Location: The Hunting Grounds.

Post by Jonas Calhoun »

A lot of times you'll see marks in the plastic, even though it's smooth...it can be a stress point where the sprue connected. You won't notice it after it's primed.

Dan
"Laugh while you can, monkey boy!" -- Lord John Whorfin
User avatar
Stu Pidasso
Posts: 20350
Joined: Thu Jul 11, 2002 7:30 pm
Location: The Human Dutch Oven.

Post by Stu Pidasso »

Sanding doesn't bother me at all.

It's filling in those stupid exposed ejector pin marks that I hate. :evil:
So me, trying to be tolerant of everybody's situations, went to a feminist picnic. Things fell apart fairly quickly after nobody made any sandwiches.
User avatar
DasPhule
Moderator
Posts: 3593
Joined: Thu Jul 11, 2002 5:31 pm
Location: Tampa, FL
Contact:

Post by DasPhule »

I recently devised a way to hide the knockout pin marks that works great for mecha. Turn em into screw heads! A simple swipe of the scriber (I use a graver) to engrave one line across te circle and tada! it's a screw head.

Erin
<*>
How about a nice cup of STFU?
http://www.fpkclub.com/ugh-models
Cenebar
Posts: 2486
Joined: Fri Jul 26, 2002 4:19 pm

Post by Cenebar »

I sanded down the sprue marks and reprimed...couldn't think of any better method or shortcut.

I got everything smooth the second time around.

Sometimes I just have to work to make it right. :D.
Zen-Builder
Posts: 2073
Joined: Sat Nov 26, 2005 6:06 pm
Location: Tokyo, Japan

Post by Zen-Builder »

For raised ejector marks, nothing helps than sanding them down.

For recessed ejector marks you can either fill them with putty or a punched out disc from sheet styrene and than sand them down.

Nasty ones are the ones located in a curve of the body, etc.

Sometimes it takes multiple passes of putty and sanding.
Post Reply