An amature scratch builds the shuttlecraft in 1/50

The place to discuss all aspects of building models from scratch.

Moderators: Joseph C. Brown, Moderators

Post Reply
User avatar
kryptosdaddy
Posts: 45
Joined: Mon Oct 31, 2011 1:25 pm
Location: COLUMBIA SC

An amature scratch builds the shuttlecraft in 1/50

Post by kryptosdaddy »

This is my first ground up scratch build. These were posted on another forum so if they seem familiar well they are`!

I'm posting this to help some of the folks here that would like to try scratching but feel daunted by the math- well I'm terrible at math!

Sometimes a little mechanical intuition is enough- enjoy CR

Based this on the OLD Technical manuals 2 pages on the shuttlecraft- copied the pages and made a paper form..

http://i1121.photobucket.com/albums/l50 ... escrap.jpg
http://i1121.photobucket.com/albums/l50 ... scrap1.jpg

Built a little frame into the top of the paper form out of sprue and then realized the solution was right in front of me- the centerline- as a plumber by reflex, the center is always a great place to start...

http://i1121.photobucket.com/albums/l50 ... pbase1.jpg

I 'm not that great at math, but I can measure- 5/16 brass came near perfect for the engines, a little wire and some .080 sheet built the 'plate' and a good bit of the supports ect.

http://i1121.photobucket.com/albums/l50 ... frame2.jpg

Now the fun part, building the thing- I started at the top, did the sides and corrected my errors then began the bottom.

http://i1121.photobucket.com/albums/l50 ... anels1.jpg

I used my drawings to cut a depth scale for the rear- now I'm building this according to those old Technical manual drawings, so this will differ from some of the other shuttle build ups I found online while researching- as the build progressed I began to add elements from other sources, after all it is make believe!

http://i1121.photobucket.com/albums/l50 ... fixed1.jpg

After several attempts I finally got a solution to the impulse engine that was satisfactory- I made a ladder and tied the ends together..
http://i1121.photobucket.com/albums/l50 ... ngine4.jpg
http://i1121.photobucket.com/albums/l50 ... ngine5.jpg

http://i1121.photobucket.com/albums/l50 ... prime2.jpg

Now I'm ready to finish!
nacelle ends were made from brass tube...

http://i1121.photobucket.com/albums/l50 ... lhell1.jpg

http://i1121.photobucket.com/albums/l50 ... lhell2.jpg

http://i1121.photobucket.com/albums/l50 ... lldone.jpg

Then some paint...

http://i1121.photobucket.com/albums/l50 ... pprime.jpg
http://i1121.photobucket.com/albums/l50 ... ryfit3.jpg

Alot of sanding and two coats of primer later it's painted...

http://i1121.photobucket.com/albums/l50 ... inted1.jpg

and then done!

http://i1121.photobucket.com/albums/l50 ... apdone.jpg

The wings were thickened, the windows and door are recessed, the globes at the ends of the nacelles are glass beads. Decals were made with a free graphics program.

About 6 weeks from paper form to finished shelf queen- there were times when I thought I had over stepped myself, but later i realized this was when I was at a point in the build where I was about to overcome a major problem. Just hang in there and try it out, you may be suprized! Be good CR
Just scratching around....
User avatar
Joseph C. Brown
Moderator
Posts: 7301
Joined: Thu Jul 11, 2002 6:13 pm
Location: Oak Ridge, TN, USA

Post by Joseph C. Brown »

Nice build sequence - it really does help to show the steps of the process. :thumbsup:
________
Joe Brown
User avatar
MillenniumFalsehood
Posts: 16974
Joined: Tue Nov 16, 2004 5:23 pm
Location: Wichita, KS, USA
Contact:

Post by MillenniumFalsehood »

The end product speaks for itself. Well done, and a very informative article. :8)
If a redhead works at a bakery, does that make him a gingerbread man?

Ponies defeat a Star Trek villain? Give them a Star Wars award ceremony!
User avatar
kryptosdaddy
Posts: 45
Joined: Mon Oct 31, 2011 1:25 pm
Location: COLUMBIA SC

Post by kryptosdaddy »

Thanks fellas, its a great feeling to beat something into shape from a pile of flat sheets!
Just scratching around....
Thundergod
Posts: 41
Joined: Thu Apr 11, 2013 3:43 am
Location: Merseyside, UK

Post by Thundergod »

Great build log . The first scratchbuild I ever did was that very craft ! ( Obviously nowhere as good as yours !) I've long considered re-visiting the subject and doing another , your thread has pushed me that little bit closer . Good , clean build . Well done . :wink:
"I'm The Lord of the Wasteland , a Modern Day Man of Steel " .
Tankmodeler
Posts: 949
Joined: Fri Jul 30, 2010 12:04 am
Location: Ontario

Post by Tankmodeler »

Well done! One of the best things about scratchbuilding is the satisfaction of finding solutions to the problems that always come up in a scratchbuilding project.

Paul
The future is in your hands. Build it!
Post Reply